When standard austenitic alloys like 316L fall short due to high mechanical loads or severe chloride stress corrosion cracking (SCC), engineers turn to duplex stainless steel. Featuring a balanced 50% austenite / 50% ferrite microstructure, duplex grades deliver roughly double the yield strength of 316L alongside superior localized corrosion resistance.
The two dominant grades in this family are Standard Duplex 2205 (UNS S32205 / S31803) and Super Duplex 2507 (UNS S32750).
Quick Verdict: Choose 2205 duplex for most chemical tankers, brackish water heat exchangers, pulp-and-paper digesters, and structural offshore components where high strength and cost-effectiveness are key. Upgrade to 2507 super duplex for warm, aerated seawater, deep-sea umbilicals, high-pressure desalination, and aggressive hot chloride/acid environments requiring a PREN > 40.
Technical Comparison: Duplex 2205 vs. Super Duplex 2507
| Property | 2205 Duplex (UNS S32205) | 2507 Super Duplex (UNS S32750) |
| EN / DIN Number | 1.4462 | 1.4410 |
| Alloy Classification | Standard Duplex | Super Duplex |
| Chromium (Cr) | 22.0 – 23.0% | 24.0 – 26.0% |
| Nickel (Ni) | 4.5 – 6.5% | 6.0 – 8.0% |
| Molybdenum (Mo) | 3.0 – 3.5% | 3.0 – 5.0% |
| Nitrogen (N) | 0.14 – 0.20% | 0.24 – 0.32% |
| PREN Value | 34 – 36 | 41 – 43 (Always > 40) |
| Min Yield Strength (0.2%) | 450 MPa (65 ksi) | 550 MPa (80 ksi) |
| Min Tensile Strength | 655 MPa (95 ksi) | 795 MPa (116 ksi) |
| Critical Pitting Temp (CPT) | ~35°C (95°F) | ~65°C – 75°C (149°F – 167°F) |
| Max Operating Temp | 300°C (572°F) | 250°C – 300°C (482°F – 572°F) |
1. Corrosion Resistance & PREN Value
The defining benchmark separating standard duplex from super duplex is the Pitting Resistance Equivalent Number (PREN), calculated as:

- Grade 2205 Duplex: Achieves a PREN of 34–36. It resists chloride stress corrosion cracking up to ~150°C and handles ambient seawater, brackish water, and moderate organic/inorganic acids reliably. However, in warm, stagnant, or chlorinated seawater (>35°C), crevice corrosion can initiate.
- Grade 2507 Super Duplex: By boosting chromium to 25%, molybdenum to 4%, and nitrogen to ~0.28%, 2507 achieves a PREN > 40 (typically 41–43). This places its corrosion performance on par with expensive 6% Mo super austenitic alloys and certain nickel alloys, making it virtually immune to pitting and crevice corrosion in hot seawater and concentrated brine.
2. Mechanical Strength & Weight Reduction
Both alloys far exceed the 205 MPa yield strength of 316L, allowing engineers to design thinner wall thicknesses for pressure vessels and piping—cutting total material weight and welding time:
- 2205 Yield Strength: 450 MPa min (~2.2× stronger than 316L).
- 2507 Yield Strength: 550 MPa min (~2.7× stronger than 316L).
Crucial Temperature Limitation (475°C Embrittlement)
Because of their high chromium and ferritic content, neither 2205 nor 2507 should be used continuously above 300°C (572°F). Prolonged exposure between 300°C and 950°C precipitates brittle intermetallic phases (such as sigma phase), severely reducing impact toughness and corrosion resistance.
3. Fabrication & Weldability Considerations
- 2205 is readily weldable using standard processes (GTAW, GMAW, SMAW, SAW) with matching ER2209 over-alloyed filler metal to restore the 50/50 austenite-ferrite phase balance in the weld bead.
- 2507 requires stricter heat-input control (typically 0.5–1.5 kJ/mm) and low interpass temperatures (<100°C–150°C) using ER2594 super duplex filler wire. Excessive heat input can form deleterious sigma phase, while overly rapid cooling can result in excessive ferrite.
4. Application Guide: 2205 vs. 2507
Choose 2205 Duplex For:
- Chemical parcel tanker cargo tanks and piping
- Pulp and paper digesters, blow tanks, and bleaching equipment
- Oil & gas onshore gathering lines and mild sour-gas separators
- Bridges, sluice gates, and coastal structural reinforcements
- Heat exchangers using brackish or cool coastal water
Choose 2507 Super Duplex For:
- Subsea umbilicals, risers, manifolds, and downhole tubulars
- Reverse osmosis (RO) high-pressure desalination piping and pumps
- Warm, aerated seawater cooling systems and firewater mains
- Flue Gas Desulfurization (FGD) scrubbers in power plants
- High-chloride chemical reactors handling sulfuric and hydrochloric acid mixtures
Frequently Asked Questions (FAQ)
Q1: Are 2205 and 2507 duplex stainless steels magnetic?
Yes. Because roughly 50% of their microstructure is ferrite (body-centered cubic), both 2205 and 2507 are noticeably magnetic—unlike non-magnetic austenitic grades like 304 and 316.
Q2: How much more expensive is 2507 compared to 2205?
Due to higher nickel, molybdenum, and chromium additions alongside tighter mill processing tolerances, 2507 typically costs 35% to 60% more per kilogram than 2205, though it remains significantly more economical than nickel-base alloys like Inconel 625 or Hastelloy C276.
Need certified 2205 or 2507 duplex plate, seamless pipe, fittings, or bar stock for marine or chemical projects? Contact Detect Metals with your specifications for a fast wholesale quote.


































